Send Data

HTTP Send Data

To send data, you must first add a device. Special read and write “API KEY” when the device is created Data processing is performed according to the access method (POST, GET, POST/GET) that is generated and determined.

For example; Let our device be in a structure that receives humidity, heat and light values. For this example, the device named “# 650 - iot_examples” was created on iothook.com. IoThook .

Let the IoT device read the data from the sensors and send this data to us once every 15 seconds, a total of 100 times.

You can access the read and write API Keys created for the #650 iot device from the IoThook dashboard.

The API ENDPOINT address we will use to send data to IoThook servers with Python is https://iothook.com/api/update/. Writing api_key information is needed to send data. You can access this KEY from the device settings page.

There are 2 required fields to send data. These fields are api_key and field_1 fields. APIKEY your device ownership field_1 absolutely must be because it validates and must have at least one data field. Other fields defined even if they are not sent, they are recorded as None.

Send JSON Data in POST with Python

In this example, JSON data is sent to the device channel named “# 650 - iot_examples” using the HTTP POST method with Python. When the data is sent successfully, Json REST output of the data is received. You can do this with the response.json() method, we are doing.

Example output:

>>> {'device': 650, 'field_1': '6', 'field_2': '3.49', 'field_3': '22', 'field_4': None, 'field_5': None, 'field_6': None, 'field_7': None, 'field_8': None, 'id': 502491, 'pub_date': '2019-08-31T01:07:29.438160', 'remote_address': '88.242.135.167&python-requests/2.18.4&HTTP/1.1'}

Send JSON Data in POST with Python Examples:

You can find this example and others at IoT Examples Github.

"""
Python ile IoThook REST Api Testi

IoThook'da her cihazin bir kimlik numarasi APIKEY'i vardir.
Bu APIKEY kullanilarak veriler IoThook'a POST metodu ile gonderilir.
5 kere 15 saniyede bir random verileri iothook'a gonderir.

Bu ornek IotHook servisine veri almak/gondermek icin baslangic seviyesinde
testlerin yapilmasini amaclamaktadir.

v1 : 11 Eylul 2017
v2 : 19 Agustos 2019
v3 : 31 Ekim 2022

Sahin MERSIN - electrocoder

Daha fazlasi icin

http://www.iothook.com
https://www.mesebilisim.com
https://mesemekatronik.com
https://electrocoder.blogspot.com
https://github.com/meseiot/iotexamples

sitelerine gidiniz.

Yayin : http://mesebilisim.com

Licensed under the Apache License, Version 2.0 (the "License").
You may not use this file except in compliance with the License.
A copy of the License is located at

http://www.apache.org/licenses/
"""

import json
import pprint
import random
import time

import requests

headers = {'Content-type': 'application/json'}

# demo account API_KEY
# https://iothook.com/en/device/data/650/
# 650 - iot_examples
API_KEY = '21579c1e874fda7276d94f3c'  # write api key
url = 'http://iothook.com/api/update/'

for i in range(5):
data = {  # write api key
    'api_key': API_KEY,  # demo hesap #650 - iot_examples
    'field_1': random.randint(1, 10),
    'field_2': round(random.uniform(0.0, 10.0), 2),
}

data_json = json.dumps(data)

response = requests.post(url, data=data_json, headers=headers)
pprint.pprint(response.json())
time.sleep(15)

Send JSON Data in POST with Python Examples 2:

You can find this example and others at IoT Examples Github.

"""
Python ile IoThook REST Api Testi

IoThook'da her cihazin bir kimlik numarasi APIKEY'i vardir.
Bu APIKEY kullanilarak veriler IoThook'a POST metodu ile gonderilir.
100 kere 15 saniyede bir random verileri iothook'a gonderir.

Bu ornek IotHook servisine veri almak/gondermek icin baslangic seviyesinde
testlerin yapilmasini amaclamaktadir.

v1 : 11 Eylul 2017
v2 : 19 Agustos 2019
v3 : 31 Ekim 2022

Sahin MERSIN - electrocoder

Daha fazlasi icin

http://www.iothook.com
https://www.mesebilisim.com
https://mesemekatronik.com
https://electrocoder.blogspot.com
https://github.com/meseiot/iotexamples

sitelerine gidiniz.

Yayin : http://mesebilisim.com

Licensed under the Apache License, Version 2.0 (the "License").
You may not use this file except in compliance with the License.
A copy of the License is located at

http://www.apache.org/licenses/
"""

import json
import pprint
import random
import time

import requests

headers = {'Content-type': 'application/json'}

# demo account API_KEY
# https://iothook.com/en/device/data/650/
# 650 - iot_examples
API_KEY = '21579c1e874fda7276d94f3c'  # write api key
url = 'http://iothook.com/api/update/'

for i in range(100):
    data = {  # write api key
        'api_key': API_KEY,  # demo hesap #650 - iot_examples
        'field_1': random.randint(1, 10),
        'field_2': round(random.uniform(0.0, 10.0), 2),
    }

    data_json = json.dumps(data)

    response = requests.post(url, data=data_json, headers=headers)
    pprint.pprint(response.json())
    time.sleep(15)

Send JSON Data in POST with Python Examples 3:

You can find this example and others at IoT Examples Github.

"""
Python ile IoThook REST Api Testi
IoThook'da her cihazin bir kimlik numarasi APIKEY'i vardir.
Bu APIKEY kullanilarak veriler IoThook'a POST metodu ile gonderilir.
1000 kere 15 saniyede bir random verileri iothook'a gonderir.
Bu ornek IotHook servisine veri almak/gondermek icin baslangic seviyesinde
testlerin yapilmasini amaclamaktadir.
v1 : 11 Eylul 2017
v2 : 19 Agustos 2019
v3 : 31 Ekim 2022
Sahin MERSIN - electrocoder
Daha fazlasi icin
http://www.iothook.com
https://www.mesebilisim.com
https://mesemekatronik.com
https://electrocoder.blogspot.com
https://github.com/meseiot/iotexamples
sitelerine gidiniz.
Yayin : http://mesebilisim.com
Licensed under the Apache License, Version 2.0 (the "License").
You may not use this file except in compliance with the License.
A copy of the License is located at
http://www.apache.org/licenses/
"""

import json
import pprint
import random
import time

import requests

headers = {'Content-type': 'application/json'}

# demo account API_KEY
# https://iothook.com/en/device/data/650/
# 650 - iot_examples
API_KEY = '21579c1e874fda7276d94f3c'  # write api key
url = 'http://iothook.com/api/update/'

for i in range(1000):
    data = {  # write api key
        'api_key': API_KEY,  # demo hesap #650 - iot_examples
        'field_1': random.randint(1, 10),
        'field_2': round(random.uniform(0.0, 10.0), 2),
    }

    data_json = json.dumps(data)

    response = requests.post(url, data=data_json, headers=headers)
    pprint.pprint(response.json())
    time.sleep(15)

Send Data in GET with Python

With the IoThook Api v6 update, it allows sending data with the GET method.

To send data, you must first add a device. Special read and write “API KEY” when the device is created Data processing is performed according to the access method (POST, GET, POST/GET) that is generated and determined.

For example; Let our device be in a structure that receives humidity, heat and light values. For this example, the device named “# 650 - iot_examples” was created on iothook.com. IoThook .

Let the IoT device read the data from the sensors and send this data to us once every 15 seconds, a total of 100 times.

You can access the read and write API Keys created for the #650 iot device from the IoThook dashboard.

The API ENDPOINT address we will use to send data to IoThook servers with Python is https://iothook.com/api/update/. Writing api_key information is needed to send data. You can access this KEY from the device settings page.

There are 2 required fields to send data. These fields are api_key and field_1 fields. APIKEY your device ownership field_1 absolutely must be because it validates and must have at least one data field. Other fields defined even if they are not sent, they are recorded as None.

Send Data in GET with Python Examples:

You can find this example and others at IoT Examples Github.

"""
Python ile IoThook REST Api Ornegi

IoThook'da her cihazin bir kimlik numarasi APIKEY'i vardir.
Bu APIKEY kullanilarak veriler IoThook'a GET metodu ile gonderilir.

Bu ornek IoThook servisine veri almak/gondermek icin baslangic seviyesinde
testlerin yapilmasini amaclamaktadir.

v1 : 20 Eylul 2017
v2 : 19 Agustos 2019
v3 : 31 Ekim 2022

Sahin MERSIN - electrocoder

Daha fazlasi icin

http://www.iothook.com
https://www.mesebilisim.com
https://mesemekatronik.com
https://electrocoder.blogspot.com
https://github.com/meseiot/iotexamples

sitelerine gidiniz.

Yayin : http://mesebilisim.com

Licensed under the Apache License, Version 2.0 (the "License").
You may not use this file except in compliance with the License.
A copy of the License is located at

http://www.apache.org/licenses/
"""

import pprint
import requests

# demo account API_KEY
# https://iothook.com/en/device/data/650/
# 650 - iot_examples
API_KEY = '21579c1e874fda7276d94f3c'  # write api key
url = 'http://iothook.com/api/update/?api_key=' + API_KEY

data = url + '&field_1=10&field_2=20&field_3=30'

response = requests.get(data)
pprint.pprint(response.json())

Send Data in GET with Python Examples 2:

You can find this example and others at IoT Examples Github.

"""
  Python ile IoThook REST Api Ornegi

  IoThook'da her cihazin bir kimlik numarasi APIKEY'i vardir.
  Bu APIKEY kullanilarak veriler IoThook'a GET metodu ile gonderilir.
  10 kere 15 saniyede bir random verileri iothook'a gonderir.


  Bu ornek IoThook servisine veri almak/gondermek icin baslangic seviyesinde
  testlerin yapilmasini amaclamaktadir.

  v1 : 20 Eylul 2017
  v2 : 19 Agustos 2019
  v3 : 31 Ekim 2022

  Sahin MERSIN - electrocoder

  Daha fazlasi icin

  http://www.iothook.com
  https://www.mesebilisim.com
  https://mesemekatronik.com
  https://electrocoder.blogspot.com
  https://github.com/meseiot/iotexamples

  sitelerine gidiniz.

  Yayin : http://mesebilisim.com

  Licensed under the Apache License, Version 2.0 (the "License").
  You may not use this file except in compliance with the License.
  A copy of the License is located at

  http://www.apache.org/licenses/
"""

import pprint
import requests
import time

# demo account API_KEY
# https://iothook.com/en/device/data/650/
# 650 - iot_examples
API_KEY = '21579c1e874fda7276d94f3c'  # write api key
url = 'http://iothook.com/api/update/?api_key=' + API_KEY

for i in range(10):
    data = url + '&field_1=10&field_2=20&field_3=30'

    response = requests.get(data)
    pprint.pprint(response.json())
    time.sleep(15)

Arduino and ESP8266

Arduino and ESP8266 HTTP POST Send Data

In this example, Arduino code is given for sending data to iothook with ESP8266 connected to Arduino Uno with RX and TX. In the example, random numbers between 0-100 were generated and the device was sent to the device with “# 650 - iot_examples” on iothook.

You can find this example and others at IoT Examples Github.

/*
  Arduino ile ESP8266 Wifi Modul Testi

  Kod Arduino ya yuklendiginde Arduino IDE nin Serial Monitor u
  ile ESP8266 arasinda haberlesme gozlenebilir.

  Arduino ile ESP8266 arasindaki iletisim Baud ayari
  115200 olmalidir.

  Arduino 0 ile 100 arasinda uretmis oldugu Random sayıyı iothook a gonderir.

  Bu cihaza ait datalar
  https://iothook.com/en/device/data/19/
  adresinden gercek zamanli olarak izlenebilir.

  Bu ornek IOThook servisine veri gondermek icin baslangic ayarlarinin
  yapilmasini amaclamaktadir.

  24 Eylul 2017
  Güncelleme : 19 Agustos 2019
  Sahin MERSIN

  Daha fazlasi icin

  http://www.iothook.com
  ve
  https://github.com/electrocoder/IOThook

  sitelerine gidiniz.
  Sorular ve destek talepleri icin
  https://github.com/electrocoder/IOThook/issues
  sayfasina gidiniz.

  Yayin ve sahiplik http://mesebilisim.com
*/

#include "SoftwareSerial.h"

String ssid = "WIFI_ID";
String password = "WIFI_PASSWORD";

SoftwareSerial esp(10, 11);// RX, TX

String data;

String server = "iothook.com";

String uri = "/api/update/";

void setup() {

  esp.begin(115200);

  Serial.begin(115200);

  Serial.println("Arduino ile ESP8266 Wifi Modul Testi");
  Serial.println("          www.IOThook.com           ");
  Serial.println("");

  reset();

  connectWifi();

}


void reset() {

  esp.println("AT+RST");

  delay(2000);

  if (esp.find("OK") ) Serial.println("Modul Reset yapildi");
  else Serial.println("Module Reset yapılamadi");

}


void connectWifi() {

  String cmd = "AT+CWJAP=\"" + ssid + "\",\"" + password + "\"";

  esp.println(cmd);

  delay(4000);

  if (esp.find("OK")) {

    Serial.println("ESP8266 Wifi ye baglandi");

  }

  else {

    connectWifi();

    Serial.println("ESP8266 Wifi ye baglanamadı!");
  }

}


void loop () {

  data = "{\"api_key\":\"58088bb005633bb39cdf3b7d\",\"field_1\":" + String(random(0, 100)) + "}";

  httppost();

  delay(5000);

}


void httppost () {

  esp.println("AT+CIPSTART=\"TCP\",\"" + server + "\",80");

  if ( esp.find("OK")) {

    Serial.println("TCP baglanti hazir");

  }
  else
    Serial.println("TCP baglanti hatali");

  delay(3000);

  String postRequest =

    "POST " + uri + " HTTP/1.0\r\n" +

    "Host: " + server + "\r\n" +

    "Accept: *" + "/" + "*\r\n" +

    "Content-Length: " + data.length() + "\r\n" +

    "Content-Type: application/x-www-form-urlencoded\r\n" +

    "\r\n" + data;

  String sendCmd = "AT+CIPSEND=";

  esp.print(sendCmd);

  esp.println(postRequest.length() );

  delay(1500);

  if (esp.find(">")) {
    Serial.println("Gonderiliyor...");
    esp.print(postRequest);

    if ( esp.find("SEND OK")) {
      Serial.println("Gonderildi :)");

      while (esp.available()) {

        String tmpResp = esp.readString();

        Serial.println(tmpResp);

      }

      esp.println("AT+CIPCLOSE");

    }
    else
      Serial.println("Gonderilemedi :(");

  }
  else
    Serial.println("Gonderim hatasi! ESP hazir degil!");
}

Arduino and ESP8266 HTTP POST Send Data 2

In this example, Arduino code is given for sending data to iothook with ESP8266 connected to Arduino Uno with RX and TX. In the example, random numbers between 0-100 were generated and the device was sent to the device with “# 650 - iot_examples” on iothook.

You can find this example and others at IoT Examples Github.

/*
  Arduino ile ESP8266 Wifi Modul Testi

  Kod Arduino ya yuklendiginde Arduino IDE nin Serial Monitor u
  ile ESP8266 arasinda haberlesme gozlenebilir.

  Arduino ile ESP8266 arasindaki iletisim Baud ayari
  115200 olmalidir.

  Arduino 0 ile 100 arasinda uretmis oldugu 2 adet Random sayıyı iothook a gonderir.
  Bu sayılar 'data' değişkeni içerisinde field_1 ve field_2 değerleridir. Bu değerler
  sensör olarak kullanılmaktadır. Sıcaklık  ve Nem gibi sensörlerinizi bu alanlara
  gönderebilirsiniz.

  Bu cihaza ait datalar
  https://iothook.com/en/device/data/12/
  adresinden gercek zamanli olarak izlenebilir.

  Bu ornek IOThook servisine veri gondermek icin baslangic ayarlarinin
  yapilmasini amaclamaktadir.

  24 Eylul 2017
  Sahin MERSIN

  Daha fazlasi icin

  http://www.iothook.com
  ve
  https://github.com/electrocoder/IOThook

  sitelerine gidiniz.
  Sorular ve destek talepleri icin
  https://github.com/electrocoder/IOThook/issues
  sayfasina gidiniz.

  Yayin ve sahiplik http://mesebilisim.com
*/

#include "SoftwareSerial.h"

String ssid = "WIFI_SSID";
String password = "WIFI_PASSWORD";

SoftwareSerial esp(10, 11);// RX, TX

String data;

String server = "iothook.com";

String uri = "/api/update/";

void setup() {

  esp.begin(115200);

  Serial.begin(115200);

  Serial.println("Arduino ile ESP8266 Wifi Modul Testi");
  Serial.println("          www.IOThook.com           ");
  Serial.println("");

  reset();

  connectWifi();

}


void reset() {

  esp.println("AT+RST");

  delay(2000);

  if (esp.find("OK") ) Serial.println("Modul Reset yapildi");
  else Serial.println("Module Reset yapılamadi");

}


void connectWifi() {

  String cmd = "AT+CWJAP=\"" + ssid + "\",\"" + password + "\"";

  esp.println(cmd);

  delay(4000);

  if (esp.find("OK")) {

    Serial.println("ESP8266 Wifi ye baglandi");

  }

  else {

    connectWifi();

    Serial.println("ESP8266 Wifi ye baglanamadı!");
  }

}


void loop () {

  data = "{\"api_key\":\"58088bb005633bb39cdf3b7d\",\"field_1\":" + String(random(0, 100)) + ",\"field_2\":" + String(random(0, 100)) + "}";

  httppost();

  delay(8000);

}


void httppost () {

  esp.println("AT+CIPSTART=\"TCP\",\"" + server + "\",80");

  if ( esp.find("OK")) {

    Serial.println("TCP baglanti hazir");

  }
  else
    Serial.println("TCP baglanti hatali");

  delay(3000);

  String postRequest =

    "POST " + uri + " HTTP/1.0\r\n" +

    "Host: " + server + "\r\n" +

    "Accept: *" + "/" + "*\r\n" +

    "Content-Length: " + data.length() + "\r\n" +

    "Content-Type: application/x-www-form-urlencoded\r\n" +

    "\r\n" + data;

  String sendCmd = "AT+CIPSEND=";

  esp.print(sendCmd);

  esp.println(postRequest.length() );

  delay(1500);

  if (esp.find(">")) {
    Serial.println("Gonderiliyor...");
    esp.print(postRequest);

    if ( esp.find("SEND OK")) {
      Serial.println("Gonderildi :)");

      while (esp.available()) {

        String tmpResp = esp.readString();

        Serial.println(tmpResp);

      }

      esp.println("AT+CIPCLOSE");

    }
    else
      Serial.println("Gonderilemedi :(");

  }
  else
    Serial.println("Gonderim hatasi! ESP hazir degil!");
}

Arduino, ESP8266, Nodemcu GET Metodu ile Veri Gönderme

IOThook Api v1.4 güncellemesi ile GET metodu ile veri göndermeye izin vermektedir.

Bu örneğe ve diğerlerine `IOTHOOK Git`_ sayfasından ulaşabilirsiniz.

Bu örnekde Arduino, ESP8266 ve NodeMCU ile ile Get metodu kullanarak veri gönderme örneği verilmiştir:

// 18.09.2017
// Guncelleme : 19.08.2019
// nodemcu ile sicaklik ve nem takibi
// electrocoder@gmail.com
// sahin mersin
// v1

#include <ESP8266WiFi.h>          //https://github.com/esp8266/Arduino

//needed for library
#include <DNSServer.h>
#include <ESP8266WebServer.h>
#include <WiFiManager.h>          //https://github.com/tzapu/WiFiManager

//for LED status
#include <Ticker.h>

#include <ESP8266HTTPClient.h>

#include "DHT.h"

#define DHTPIN 4     // what digital pin we're connected to   // D2 - GPIO4
#define DHTTYPE DHT11

DHT dht(DHTPIN, DHTTYPE);

Ticker ticker;

void tick()
{
  //toggle state
  int state = digitalRead(BUILTIN_LED);  // get the current state of GPIO1 pin
  digitalWrite(BUILTIN_LED, !state);     // set pin to the opposite state
}

//gets called when WiFiManager enters configuration mode
void configModeCallback (WiFiManager *myWiFiManager) {
  Serial.println("Entered config mode");
  Serial.println(WiFi.softAPIP());
  //if you used auto generated SSID, print it
  Serial.println(myWiFiManager->getConfigPortalSSID());
  //entered config mode, make led toggle faster
  ticker.attach(0.2, tick);
}


void setup() {
  // put your setup code here, to run once:
  Serial.begin(115200);

  //set led pin as output
  pinMode(BUILTIN_LED, OUTPUT);

  // start ticker with 0.5 because we start in AP mode and try to connect
  ticker.attach(0.6, tick);

  //WiFiManager
  //Local intialization. Once its business is done, there is no need to keep it around
  WiFiManager wifiManager;
  //reset settings - for testing
  //wifiManager.resetSettings();

  //set callback that gets called when connecting to previous WiFi fails, and enters Access Point mode
  wifiManager.setAPCallback(configModeCallback);

  //fetches ssid and pass and tries to connect
  //if it does not connect it starts an access point with the specified name
  //here  "AutoConnectAP"
  //and goes into a blocking loop awaiting configuration
  if (!wifiManager.autoConnect("MeseIoT", "MeseIoT**")) {
    Serial.println("failed to connect and hit timeout");
    //reset and try again, or maybe put it to deep sleep
    ESP.reset();
    delay(1000);
  }

  //if you get here you have connected to the WiFi
  Serial.println("connected...yeey :)");
  ticker.detach();
  //keep LED on
  digitalWrite(BUILTIN_LED, LOW);

  dht.begin();
}


void loop() {
  // Wait a few seconds between measurements.
  delay(2000);

  // Reading temperature or humidity takes about 250 milliseconds!
  // Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
  float h = dht.readHumidity();
  // Read temperature as Celsius (the default)
  float t = dht.readTemperature();
  // Read temperature as Fahrenheit (isFahrenheit = true)
  float f = dht.readTemperature(true);

  // Check if any reads failed and exit early (to try again).
  if (isnan(h) || isnan(t) || isnan(f)) {
    Serial.println("Failed to read from DHT sensor!");
    return;
  }

  // Compute heat index in Fahrenheit (the default)
  float hif = dht.computeHeatIndex(f, h);
  // Compute heat index in Celsius (isFahreheit = false)
  float hic = dht.computeHeatIndex(t, h, false);

  Serial.print("Humidity: ");
  Serial.print(h);
  Serial.print(" %\t");
  Serial.print("Temperature: ");
  Serial.print(t);
  Serial.print(" *C ");
  Serial.print(f);
  Serial.print(" *F\t");
  Serial.print("Heat index: ");
  Serial.print(hic);
  Serial.print(" *C ");
  Serial.print(hif);
  Serial.println(" *F");

  ///
  HTTPClient http;

  // configure server and url
  http.begin("http://iothook.com/api/update/?api_key=58088bb005633bb39cdf3b7d&field_1=" + String(t) + "&field_2=" + String(h) + "");
  //http.begin("192.168.1.12", 80, "/test.html");

  Serial.print("[HTTP] GET...\n");
  // start connection and send HTTP header
  int httpCode = http.GET();
  if (httpCode > 0) {
    // HTTP header has been send and Server response header has been handled
    Serial.printf("[HTTP] GET... code: %d\n", httpCode);

    // file found at server
    if (httpCode == HTTP_CODE_OK) {

      // get lenght of document (is -1 when Server sends no Content-Length header)
      int len = http.getSize();

      // create buffer for read
      uint8_t buff[128] = { 0 };

      // get tcp stream
      WiFiClient * stream = http.getStreamPtr();

      // read all data from server
      while (http.connected() && (len > 0 || len == -1)) {
        // get available data size
        size_t size = stream->available();

        if (size) {
          // read up to 128 byte
          int c = stream->readBytes(buff, ((size > sizeof(buff)) ? sizeof(buff) : size));

          // write it to Serial
          Serial.write(buff, c);

          if (len > 0) {
            len -= c;
          }
        }
        delay(1);
      }

      Serial.println();
      Serial.print("[HTTP] connection closed or file end.\n");

    }
  } else {
    Serial.printf("[HTTP] GET... failed, error: %s\n", http.errorToString(httpCode).c_str());
  }

  http.end();
  ////
  delay(13000);
}

GO GET Metodu ile Veri Gönderme

IOThook Api v1.4 güncellemesi ile GET metodu ile veri göndermeye izin vermektedir.

Bu örneğe ve diğerlerine `IOTHOOK Git`_ sayfasından ulaşabilirsiniz.

Bu örnekde GO dili ile ile Get metodu kullanarak veri gönderme örneği verilmiştir:

// 04 Eylul 2017
// Guncelleme: 19 Agustos 2019
// Sahin MERSIN
// iothook.com
// postman kullanilarak olusturulmustur


package main

import (
    "fmt"
    "net/http"
    "io/ioutil"
)

func main() {

    url := "http://iothook.com/api/update?api_key=58088bb005633bb39cdf3b7d&field_1=10&field_2=2&field_3=3"

    req, _ := http.NewRequest("GET", url, nil)

    req.Header.Add("cache-control", "no-cache")

    res, _ := http.DefaultClient.Do(req)

    defer res.Body.Close()
    body, _ := ioutil.ReadAll(res.Body)

    fmt.Println(res)
    fmt.Println(string(body))

}

PHP GET Metodu ile Veri Gönderme

IOThook Api v1.4 güncellemesi ile GET metodu ile veri göndermeye izin vermektedir.

Bu örneğe ve diğerlerine `IOTHOOK Git`_ sayfasından ulaşabilirsiniz.

Bu örnekde PHP dili ile ile Get metodu kullanarak veri gönderme örneği verilmiştir:

// 04 Eylul 2017
// Guncelleme: 19 Agustos 2019
// Sahin MERSIN
// iothook.com
// postman kullanilarak olusturulmustur

<?php

$request = new HttpRequest();
$request->setUrl('http://iothook.com/api/update');
$request->setMethod(HTTP_METH_GET);

$request->setQueryData(array(
  'api_key' => '58088bb005633bb39cdf3b7d',
  'field_1' => '10',
  'field_2' => '2',
  'field_3' => '3'
));

$request->setHeaders(array(
  'postman-token' => '791ba738-7cb8-a920-0e5c-883cfb3e4498',
  'cache-control' => 'no-cache'
));

try {
  $response = $request->send();

  echo $response->getBody();
} catch (HttpException $ex) {
  echo $ex;
}

NodeJS GET Metodu ile Veri Gönderme

IOThook Api v1.4 güncellemesi ile GET metodu ile veri göndermeye izin vermektedir.

Bu örneğe ve diğerlerine `IOTHOOK Git`_ sayfasından ulaşabilirsiniz.

Bu örnekde NodeJS Native metodu kullanarak veri gönderme örneği verilmiştir:

// 04 Eylul 2017
// Guncelleme: 19 Agustos 2019
// Sahin MERSIN
// iothook.com
// postman kullanilarak olusturulmustur

var http = require("http");

var options = {
  "method": "GET",
  "hostname": "iothook.com",
  "port": null,
  "path": "/api/update?api_key=58088bb005633bb39cdf3b7d&field_1=10&field_2=2&field_3=3",
  "headers": {
    "cache-control": "no-cache",
    "postman-token": "033da3c8-6196-cd49-f72d-1850a7d18500"
  }
};

var req = http.request(options, function (res) {
  var chunks = [];

  res.on("data", function (chunk) {
    chunks.push(chunk);
  });

  res.on("end", function () {
    var body = Buffer.concat(chunks);
    console.log(body.toString());
  });
});

req.end();

Javascript Jquery Ajax GET Metodu ile Veri Gönderme

IOThook Api v1.4 güncellemesi ile GET metodu ile veri göndermeye izin vermektedir.

Bu örneğe ve diğerlerine `IOTHOOK Git`_ sayfasından ulaşabilirsiniz.

Bu örnekde NodeJS Native metodu kullanarak veri gönderme örneği verilmiştir:

// 04 Eylul 2017
// Guncelleme: 19 Agustos 2019
// Sahin MERSIN
// iothook.com
// postman kullanilarak olusturulmustur

var settings = {
  "async": true,
  "crossDomain": true,
  "url": "http://iothook.com/api/update?api_key=58088bb005633bb39cdf3b7d&field_1=10&field_2=2&field_3=3",
  "method": "GET",
  "headers": {
    "cache-control": "no-cache",
  }
}

$.ajax(settings).done(function (response) {
  console.log(response);
});

Java Unirest GET Metodu ile Veri Gönderme

IOThook Api v1.4 güncellemesi ile GET metodu ile veri göndermeye izin vermektedir.

Bu örneğe ve diğerlerine `IOTHOOK Git`_ sayfasından ulaşabilirsiniz.

Bu örnekde NodeJS Native metodu kullanarak veri gönderme örneği verilmiştir:

// 04 Eylul 2017
// Guncelleme: 19 Agustos 2019
// Sahin MERSIN
// iothook.com
// postman kullanilarak olusturulmustur

HttpResponse<String> response = Unirest.get("http://iothook.com/api/update?api_key=58088bb005633bb39cdf3b7d&field_1=10&field_2=2&field_3=3")
  .header("cache-control", "no-cache")
  .asString();

Java Unirest GET Metodu ile Veri Gönderme

IOThook Api v1.4 güncellemesi ile GET metodu ile veri göndermeye izin vermektedir.

Bu örneğe ve diğerlerine `IOTHOOK Git`_ sayfasından ulaşabilirsiniz.

Bu örnekde NodeJS Native metodu kullanarak veri gönderme örneği verilmiştir:

// 04 Eylul 2017
// Guncelleme: 19 Agustos 2019
// Sahin MERSIN
// iothook.com
// postman kullanilarak olusturulmustur

OkHttpClient client = new OkHttpClient();

Request request = new Request.Builder()
  .url("http://iothook.com/api/update?api_key=58088bb005633bb39cdf3b7d&field_1=10&field_2=2&field_3=3")
  .get()
  .addHeader("cache-control", "no-cache")
  .build();

Response response = client.newCall(request).execute();